Scopus
YÖKSİS DOI Eşleşti
SJR Q1
Microstructure-property relationship in explosively welded duplex stainless steel-steel
Materials Science and Engineering A · Aralık 2003
YÖKSİS Kayıtları
Microstructure\u2013property relationship in explosively welded duplex stainless steel\u2013steel
Materials Science and Engineering: A · 2003 SCI
Prof. Dr. MUSTAFA ACARER →
YÖKSİS Kayıtları — ISSN Eşleşmesi
Impact toughness and microstructure of continuous steel wire reinforced cast iron composite
2009 ISSN: 09215093 SCI 9 atıf
Prof. Dr. RECAİ KUŞ →
Investigation of the tensile properties of continuous steel wire reinforced gray cast iron composite
2011 ISSN: 09215093 SCI
Prof. Dr. RECAİ KUŞ →
Impact toughness and microstructure of continuous steel wire reinforced cast iron composite
2009 ISSN: 0921-5093 SCI-Expanded
Prof. Dr. RECAİ KUŞ →
Investigation of the tensile properties of continuous steel wire reinforced gray cast iron composite
2011 ISSN: 0921-5093 SCI-Expanded
Prof. Dr. RECAİ KUŞ →
Microstructure\u2013property relationship in explosively welded duplex stainless steel\u2013steel
2003 ISSN: 0921-5093 SCI
Prof. Dr. MUSTAFA ACARER →
Makale Bilgileri
ISSN09215093
Yayın TarihiAralık 2003
Cilt / Sayfa363 · 290-296
Scopus ID2-s2.0-0242574688
Özet
Duplex stainless steel (2205 grade) and vessel steel (DIN-P355GH grade) were cladded by explosive welding. The relationship between hardness, tensile shear strength and toughness and microstructure of cladded materials were evaluated. The bond interface of the cladded materials shows a wavy morphology. The hardness was similar in the base and flyer plate near the bond interface while a general increase was observed in both base and flyer plate about 25 μm away from interface. Tensile shear strength test results showed that duplex stainless steel-vessel steel cladded materials exhibit an acceptable joint strength. The impact toughness of the cladded materials at a given test temperature is found significantly higher than that of the base material alone because of the high impact toughness of the duplex stainless steel layer. Consequently, mechanical and corrosion properties of the low carbon steels can be increased by explosive cladding with duplex stainless steel. © 2003 Elsevier B.V. All rights reserved.
Yazarlar (2)
1
Ramazan Kacar
2
Mustafa Acarer
Anahtar Kelimeler
Duplex stainless steel
Explosive welding
Fracture toughness
Tensile shear strength
Kurumlar
Karabük Üniversitesi
Karabuk Turkey
Son Atıflar
Vacuum diffusion bonding strengthening mechanical properties of 304 stainless steel/low carbon steel composites by in-situ eutectic reaction
Vacuum
· 2025 · DOI
Impact Welding of Aluminum AA1060 and Copper T2 Sheets by Vaporizing Foil Actuator: Microstructure, Mechanical Properties, and Electrical Conductivity
Journal of Materials Engineering and Performance
· 2025 · DOI
Influence of heat treatment on the microstructure and thermal conductivity of duplex stainless steel manufactured via wire arc additive manufacturing
Proceedings of the Institution of Mechanical Engineers Part E Journal of Process Mechanical Engineering
· 2025 · DOI
An Investigation about Microstructures, Mechanical Properties and Corrosion Behaviour of the TIG - MIG Hybrid Welded Dissimilar UNS 2205 and is 2062 Steels
Key Engineering Materials
· 2024 · DOI
Interfacial microstructure evolution and mechanical properties of TIG welding joints of AISI 304/Q235B rolled composite plates
Journal of Adhesion Science and Technology
· 2024 · DOI
Effect of explosive welding on the interface characteristics of S32750/Q245R composite plate
Composite Interfaces
· 2024 · DOI
Investigation of mechanical and microstructural properties in joining dissimilar P355GH and stainless 316L steels by TIG welding process
International Journal of Pressure Vessels and Piping
· 2023 · DOI
Water-augmented vaporizing foil actuator welding: Process performance and mechanisms clarifications
Journal of Materials Processing Technology
· 2023 · DOI
Effect of heat treatment on the welded joint of X70 steel joined to duplex stainless steel by gas tungsten arc welding
International Journal of Advanced Manufacturing Technology
· 2023 · DOI
Failure analysis of 2205 duplex stainless steel connecting pipe for composite plate pressure vessel in a high pressure gas field
International Journal of Pressure Vessels and Piping
· 2023 · DOI
Scimago Dergi (ISSN Eşleşmesi)
Materials Science and Engineering: A
Q1
SJR Skoru1,955
H-Index292
YayıncıElsevier Ltd
ÜlkeUnited Kingdom
Condensed Matter Physics (Q1)
Materials Science (miscellaneous) (Q1)
Mechanical Engineering (Q1)
Mechanics of Materials (Q1)
Nanoscience and Nanotechnology (Q1)
Metrikler
148
Atıf
2
Yazar
4
Anahtar Kelime