Scopus
YÖKSİS DOI Eşleşti
SJR Q1
An investigation on the explosive cladding of 316L stainless steel-din-P355GH steel
Journal of Materials Processing Technology · Ekim 2004
YÖKSİS Kayıtları
An investigation on the explosive cladding of 316L stainless steel-din-P355GH steel
Journal of Materials Processing Technology · 2004 SCI
Prof. Dr. MUSTAFA ACARER →
YÖKSİS Kayıtları — ISSN Eşleşmesi
An investigation on the explosive cladding of 316L stainless steel-din-P355GH steel
2004 ISSN: 0924-0136 SCI
Prof. Dr. MUSTAFA ACARER →
Makale Bilgileri
ISSN09240136
Yayın TarihiEkim 2004
Cilt / Sayfa152 · 91-96
Scopus ID2-s2.0-4344716297
Özet
In this study, 316L stainless steel and DIN-P355GH grade vessel steel were cladded by explosive welding technique. Microstructure, hardness and tensile shear strength, and fracture toughness of the cladded metals were evaluated. The bond interface of the cladded metals shows a wavy morphology. The hardness was increased in the parent and flyer plate near the bond interface while a general decrease was observed in both parent and flyer plate away from welded interface. Tensile shear test results showed that the bonding is acceptable. The impact toughness of the cladded metals at a given test temperature is found significantly higher than that of parent plate alone because of the high impact toughness of 316L austenitic stainless steel layer. Consequently, mechanical properties of the low-carbon steels can be increased by explosive cladding with austenitic stainless steel. © 2004 Elsevier B.V. All rights reserved.
Yazarlar (2)
1
Ramazan Kacar
2
Mustafa Acarer
Anahtar Kelimeler
316L stainless steel
Explosive welding
Fracture toughness
Tensile shear strength
Kurumlar
Karabük Üniversitesi
Karabuk Turkey
Son Atıflar
Effect of hot rolling conditions on the microstructure and mechanical properties of Incoloy 825/API X65 clad plates
Journal of Materials Research and Technology
· 2026 · DOI
The punching of DP1000 automotive steel–Al laminate composite fabricated by explosive welding: Effect of tool geometry on cutting force and cut surfaces
Proceedings of the Institution of Mechanical Engineers Part E Journal of Process Mechanical Engineering
· 2026 · DOI
Microstructure Characterization of Bending Effects in 304L Stainless Steel Cladded with Low-Alloy Steel Weld
Steel Research International
· 2026 · DOI
Study on the deformation behavior and mechanical properties of S17400/Q345R composite plates through asymmetric different-temperature rolling
International Journal of Advanced Manufacturing Technology
· 2026 · DOI
Regulating Behaviors of Explosive-Bonded Wavy Interface on Tensile Properties of 304L/533B CL.1 Clad Plate
Advanced Engineering Materials
· 2026 · DOI
Effects of heat treatment on microstructure, mechanical properties and irradiation response of LPBF GH3535 superalloy
Materials Characterization
· 2025 · DOI
The synergistic effect of microstructure evolution on corrosion resistance-mechanical properties of carbon steel/stainless steel cladding tubes during heat treatment
Corrosion Science
· 2025 · DOI
Study on parametric optimization, microstructure, and corrosion behaviour of explosive weld AZ31B and al 5052 laminate composite with reinforcements
International Journal on Interactive Design and Manufacturing
· 2025 · DOI
Interfacial characteristics and in situ nanoindentation analysis of hot-roll-bonded 316L stainless steel/Q370qE bridge steel clad plate
Journal of Materials Research
· 2025 · DOI
Influence mechanisms of Y-direction magnetic field-assisted laser penetration welding on the molten pool behavior and joint characteristics of layered DSS2205/X65 bimetallic composite
Journal of Manufacturing Processes
· 2025 · DOI
Scimago Dergi (ISSN Eşleşmesi)
Journal of Materials Processing Technology
Q1
SJR Skoru1,885
H-Index239
YayıncıElsevier B.V.
ÜlkeNetherlands
Ceramics and Composites (Q1)
Computer Science Applications (Q1)
Industrial and Manufacturing Engineering (Q1)
Metals and Alloys (Q1)
Modeling and Simulation (Q1)
Metrikler
178
Atıf
2
Yazar
4
Anahtar Kelime